MAG 250

[aspicyx]

Некорректное разрешение экрана. По дефолту в биосе PAL 576x720. Нужно выставить в биосе параметры, соответствующие вашему тв, в первых двух строках должны совпадать (разрешение приставки-разрешение тв). Если поставить Auto или аналоговое, то по hdmi будет через раз включаться в лучшем случае.

Выставленно все как положенно
1280Х720
720
Телевизор тот же (4К) работало без проблем до вчерашнего дня.

[vugluskr]

Выставленно все как положенно
1280Х720
720
Телевизор тот же (4К) работало без проблем до вчерашнего дня.

Поставьте FullHD

[aspicyx]

Поставьте FullHD

Ставил, результат тот же как описано выше.

[vugluskr]

Как вариант - проверить на другом тв, попробовать другой hdmi-кабель. Бывают еще проблемы с м/с hdmi-hub в телевизоре, которая дохнет частично, т.е. сначала один разъём "отваливается", потом - остальные.

[aspicyx]

Как вариант - проверить на другом тв, попробовать другой hdmi-кабель. Бывают еще проблемы с м/с hdmi-hub в телевизоре, которая дохнет частично, т.е. сначала один разъём "отваливается", потом - остальные.

Я пока подключил на этом же телевизоре,этим же кабелем но в другой разьем HDMI все работает без проблем, похоже именно тот HDMI выход барахлит, но тогда так и не понятно почему есть картинка когда идет загрузка там где лого Infomir а потом сигнал пропадает...

[vugluskr]

Я пока подключил на этом же телевизоре,этим же кабелем но в другой разьем HDMI все работает без проблем, похоже именно тот HDMI выход барахлит, но тогда так и не понятно почему есть картинка когда идет загрузка там где лого Infomir а потом сигнал пропадает...

Загрузочный экран с логотипом идет всегда с минимальным разрешением/настройками, так что видно на любом телевизоре, затем идет смена разрешения. Я точно так же замучался подключать к монитору через перходник hdmi-dvi, лого грузилось без проблем, затем out of range. Там дело оказалось в кабелях/переходниках, ниже была тема.

[ZoYa-MAG-250]

[ATTACH=CONFIG]11686[/ATTACH][ATTACH=CONFIG]11687[/ATTACH]

этой приставке уже 2 года, ревизия ещё 1.5. от времени стала подванивать, греется как утюг, зависала при старте, не успевал прошить из биоса
с такой конструкцией (одного радиатора ей уже мало) уже сутки вещает HD канал

А проверять и перепаивать электролиты на плате не пробовали?

[ZoYa-MAG-250]

Раз в два дня зависает приставка, и не включается, только спустя после 1час-2 если отключить питание, начинает загружаться. Если ставлю прошивку на nand2 то проблема почти исчезает, ну может раз в 3недели зависнет. Можно ли как то форматнуть nand1 или всю память? или что это может быть? Пробывал разные прошивки.

Сменой загрузочного NAND - всё-таки что-то улучшилось в работе? или всё по прежнему?

[ZoYa-MAG-250]

А ты случаем костыль не ставил на неё отсюда ?
пРИсТаВка - Русское Интернет Телевидение

ссылка не работает - что-то изменилось в структуре форума.

Сдохли приставки у тех, кто костыл ставил !

А что за "костыль"? Это вы про радиатор?

[Dr_Vao]

А что за "костыль"? Это вы про радиатор?

Это не про радиатор.

При помощи "костыля" можно изменить идентификатор приставки, мак-адрес, серийный номер - все это применимо к маг250 (было)...

[inspire_87]

Добрый день!



Приставка MAG 250 переодически несколько раз в день зависала, перезагрузка не помогала, через время включалась и работала пару минут и зависала. Теперь постоянно при включении горит Loading ... пробовал прошить как через USB так и через мультикаст, вылазит ошибка Error writing image to flash. Waiting operator command. В биосе поля Ver Bootst. Ver. Userfs пустые, я так понимаю реанимировать приставку без СЦ не удасться? умерла память или прошивка слетела?

вот что удалось увидеть через UART, куда копать подскажет ктото?

Spoiler

Board: MAG250 [32-bit mode]


U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047

DRAM: 256 MiB
NOR: 1 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Press "Menu" for enter menu
Hit any key to stop autoboot: 0
### JFFS2 loading 'uImage' to 0x80000000
Scanning JFFS2 FS: . done.
### JFFS2 load complete: 3230449 bytes loaded to 0x80000000
## Booting image at 80000000 ...
Image Name: MAG250 SH4 Kernel Linux 2.6.17
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 3230385 Bytes = 3.1 MiB
Load Address: 80800000
Entry Point: 80801000
Verifying Checksum ... Bad Data CRC

Warning: MAC addresses don't match:
HW MAC address: FF:FF:FF:FF:FF:FF
"ethaddr" value: 00:00:00:00:00:00

sing MAC Address 00:00:00:00:00:00
STM-GMAC: IC+ IP101 found
STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
STM-GMAC: PHY auto-negotiate timed out
STM-GMAC: *Warning* no link detected
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10

[kommux]

было несколько лет назад,прошивать нужно начинать прошей от инфомира,получилось с 15 или с 20 раза с флешки через задний вход

[inspire_87]

Вот такое вылазит еще, возможно NAND умер?

Spoiler

Board: MAG250 [32-bit mode]
U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047
DRAM: 256 MiB
NOR: 1 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Press "Menu" for enter menu
Loading image form multicast channel 224.50.0.70:9000 is started...

Warning: MAC addresses don't match:
HW MAC address: ***************
"ethaddr" value: ****************
Using MAC Address ******************
STM-GMAC: IC+ IP101 found
STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
STM-GMAC: PHY auto-negotiate timed out
STM-GMAC: *Warning* no link detected
McloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTTT
Abort

Error MC Upgrade!!!
Loading image form multicast channel 224.50.0.70:9000 is started...

Warning: MAC addresses don't match:
HW MAC address: ***************
"ethaddr" value: ***************
Using MAC Address ****************
STM-GMAC: IC+ IP101 found
STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
STM-GMAC: 100Mbs full duplex link detected
McloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTTTMcloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTT############################################## ###################
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
##############
End receive image
Bytes transferred = 6378399 (61539f hex)
## Booting image at 80000000 ...
Image Name: SH4 MAG250 Bootstrap Ver:002
Image Type: SH-4 Linux Kernel Image (uncompressed)
Data Size: 6378335 Bytes = 6.1 MiB
Load Address: 80800000
Entry Point: 80801000
Verifying Checksum ... OK
Read data: 80000040 length: 875 (0x36b)
Signature OK!!
Signature OK!!
OK

Starting kernel nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200 - 0x00000000 - 0 ...

Linux version 2.6.23.17_stm23_A23-MAG250_7105 (root@Server01.localdomain) (gcc version 4.2.4 (snapshot) (STMicroelectronics/Linux Base 4.2.4-44)) #2 PREEMPT Thu Jun 8 17:00:37 EEST 2017
Booting machvec: mag250
Node 0: start_pfn = 0x40000, low = 0x4f800
Zone PFN ranges:
Normal 262144 -> 325632
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 262144 -> 325632
Infomir,LLC MAG250 board initialisation
STx7105 version 4.x
Built 1 zonelists in Zone order. Total pages: 62992
Kernel command line: nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200
bpa2: partition 'bigphysarea' created at 0x41031000, size 8192 kB (0x00800000 B)
PID hash table entries: 1024 (order: 10, 4096 bytes)
Using tmu for system timer
Using 25.000 MHz high precision timer.
Console: colour dummy device 80x25
console [ttyAS0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 228864k/253952k available (3095k kernel code, 740k data, 2384k init)
PVR=04909200 CVR=60880000 PRR=00009e40
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STx7105
NET: Registered protocol family 16
Configuring FLASH for boot-from-NOR
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: SuperH clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.
JFS: nTxBlock = 1788, nTxLock = 14311
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
STMicroelectronics ASC driver initialized
stasc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stasc
stasc.1: ttyAS1 at MMIO 0xfd031000 (irq = 122) is a stasc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
platform registration... <7>done!
GMAC - user ID: 0x10, Synopsys ID: 0x33
eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
IO base addr: 0xfd110000)
STMMAC MII Bus: probed
eth0: PHY ID 02430c54 at 1 IRQ -1 (0:01) active
ICPlus IP101A: Registered new driver
ICPlus IP1001: Registered new driver
ICPlus IP175C: Registered new driver
physmap platform flash device: 00100000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 5 MTD partitions on "physmap-flash":
0x00000000-0x00050000 : "BootLoader"
first erase region 0 for slave @ 0
0x00050000-0x000a0000 : "Upgrade Boot"
first erase region 0 for slave @ 327680
0x000a0000-0x000e0000 : "User's FS"
first erase region 0 for slave @ 655360
0x000e0000-0x000f0000 : "Logo"
first erase region 0 for slave @ 917504
0x000f0000-0x00100000 : "BootLoader Enviroment"
first erase region 1 for slave @ 983040
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
stm-ehci stm-ehci.1: st-ehci
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
stm-ohci stm-ohci.1: stm-ohci
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st-coprocessor-0: No RAM reserved
st231.0 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
st-coprocessor-1: No RAM reserved
st231.1 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
stm_rng hardware driver 1.0 configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memoryzroute: SIOCADDRT: Network is down
net.core.rmem_max = 1000000
Starting S20uhdcp...
check_usbman:
check_mcman:mcman=on
## Error: "update_url" not defined
## Error: "mcip_img_conf" not defined
## Error: "mcport_img_conf" not defined
mcip_img=224.50.0.51
mcport_img=9001
## Error: "oppubKEY" not defined
Print recv_start to Monitor
PHY: 0:01 - Link is Up - 100/Full
Sat Jan 1 00:00:02 UTC 2000
IP: 192.168.243.249
MAC: ***********
Wrong offset in file /usr/bin/radix64.KEY -263 0

Signature not correct
Error: Not correct digital signature operator's key
Use default operator's keys
Connect to IP:224.50.0.51 port:9001
Create new file. File size:74600074
SN 0 offs 432480
Print recv_success to Monitor
Start Write Image to nand flash
4096+0 records in
4096+0 records out
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x00000000
Bad eraseblock 3 at 0x00060000
Bad eraseblock 8 at 0x00100000
Bad eraseblock 9 at 0x00120000
Bad eraseblock 10 at 0x00140000
Bad eraseblock 11 at 0x00160000
Bad eraseblock 16 at 0x00200000
Bad eraseblock 17 at 0x00220000
Bad eraseblock 18 at 0x00240000
Bad eraseblock 19 at 0x00260000
Bad eraseblock 24 at 0x00300000
Bad eraseblock 25 at 0x00320000
Bad eraseblock 26 at 0x00340000
Bad eraseblock 27 at 0x00360000
Bad eraseblock 32 at 0x00400000
Bad eraseblock 33 at 0x00420000
Bad eraseblock 34 at 0x00440000
Bad eraseblock 35 at 0x00460000
Bad eraseblock 40 at 0x00500000
Bad eraseblock 41 at 0x00520000
Bad eraseblock 43 at 0x00560000
Bad eraseblock 48 at 0x00600000
Bad eraseblock 49 at 0x00620000
Bad eraseblock 50 at 0x00640000
Bad eraseblock 51 at 0x00660000
Bad eraseblock 56 at 0x00700000
Bad eraseblock 57 at 0x00720000
Bad eraseblock 58 at 0x00740000
Bad eraseblock 59 at 0x00760000
Bad eraseblock 64 at 0x00800000
Bad eraseblock 65 at 0x00820000
Bad eraseblock 66 at 0x00840000
Bad eraseblock 67 at 0x00860000
Bad eraseblock 72 at 0x00900000
Bad eraseblock 83 at 0x00a60000
Bad eraseblock 282 at 0x02340000
Bad eraseblock 283 at 0x02360000
Bad eraseblock 380 at 0x02f80000
Bad eraseblock 497 at 0x03e20000
Bad eraseblock 537 at 0x04320000
Bad eraseblock 538 at 0x04340000
5 cmdlinepart partitions found on MTD device stm-nand-flex.1
Creating 5 MTD partitions on "stm-nand-flex.1":
0x00000000-0x00400000 : "Kernel"
0x00400000-0x07c00000 : "RootFs"
0x07c00000-0x08000000 : "Kernel2"
0x08000000-0x0f800000 : "RootFs2"
0x0f800000-0x10000000 : "Userfs"
Bad block at 0, 1 block(s) from 0 will be skipped
Bad block at 60000, 1 block(s) from 60000 will be skipped
Bad block at 100000, 1 block(s) from 100000 will be skipped
Bad block at 120000, 1 block(s) from 120000 will be skipped
Bad block at 140000, 1 block(s) from 140000 will be skipped
Bad block at 160000, 1 block(s) from 160000 will be skipped
Bad block at 200000, 1 block(s) from 200000 will be skipped
Bad block at 220000, 1 block(s) from 220000 will be skipped
Bad block at 240000, 1 block(s) from 240000 will be skipped
Bad block at 260000, 1 block(s) from 260000 will be skipped
Bad block at 300000, 1 block(s) from 300000 will be skipped
Bad block at 320000, 1 block(s) from 320000 will be skipped
Bad block at 340000, 1 block(s) from 340000 will be skipped
Bad block at 360000, 1 block(s) from 360000 will be skipped
Data did not fit into device, due to bad blocks
: Inappropriate ioctl for device
/usr/bin/img_write.sh: line 245: //: Permission denied
Bad block at 0, 1 block(s) from 0 will be skipped
Bad block at 60000, 1 block(s) from 60000 will be skipped
Bad block at 100000, 1 block(s) from 100000 will be skipped
Bad block at 120000, 1 block(s) from 120000 will be skipped
Bad block at 140000, 1 block(s) from 140000 will be skipped
Bad block at 160000, 1 block(s) from 160000 will be skipped
Bad block at 200000, 1 block(s) from 200000 will be skipped
Bad block at 220000, 1 block(s) from 220000 will be skipped
Bad block at 240000, 1 block(s) from 240000 will be skipped
Bad block at 260000, 1 block(s) from 260000 will be skipped
Bad block at 300000, 1 block(s) from 300000 will be skipped
Bad block at 320000, 1 block(s) from 320000 will be skipped
Bad block at 340000, 1 block(s) from 340000 will be skipped
Bad block at 360000, 1 block(s) from 360000 will be skipped
Data did not fit into device, due to bad blocks
: Inappropriate ioctl for device
Print write_error to Monitor
Wait command from operator
Log ip parameters must be set
Connect to IP: port:0

[jevvol]

Вот такое вылазит еще, возможно NAND умер?

Spoiler

Board: MAG250 [32-bit mode]
U-Boot 1.3.1 (Nov 7 2011 - 20:45:09) - stm23_0047
DRAM: 256 MiB
NOR: 1 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Press "Menu" for enter menu
Loading image form multicast channel 224.50.0.70:9000 is started...

Warning: MAC addresses don't match:
HW MAC address: ***************
"ethaddr" value: ****************
Using MAC Address ******************
STM-GMAC: IC+ IP101 found
STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
STM-GMAC: PHY auto-negotiate timed out
STM-GMAC: *Warning* no link detected
McloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTTT
Abort

Error MC Upgrade!!!
Loading image form multicast channel 224.50.0.70:9000 is started...

Warning: MAC addresses don't match:
HW MAC address: ***************
"ethaddr" value: ***************
Using MAC Address ****************
STM-GMAC: IC+ IP101 found
STM-GMAC: PHY address mismatch with hardware (hw 8 != 1)
STM-GMAC: 100Mbs full duplex link detected
McloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTTTMcloadStart
*** Warning: no boot file name; using 'C0A8F3F9.img'
Load from multicast group: IP - 224.50.0.70 Port - 9000
Load address: 0x80000000
Loading: *
Starting receive image
TTTT############################################## ###################
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
################################################## ###############
##############
End receive image
Bytes transferred = 6378399 (61539f hex)
## Booting image at 80000000 ...
Image Name: SH4 MAG250 Bootstrap Ver:002
Image Type: SH-4 Linux Kernel Image (uncompressed)
Data Size: 6378335 Bytes = 6.1 MiB
Load Address: 80800000
Entry Point: 80801000
Verifying Checksum ... OK
Read data: 80000040 length: 875 (0x36b)
Signature OK!!
Signature OK!!
OK

Starting kernel nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200 - 0x00000000 - 0 ...

Linux version 2.6.23.17_stm23_A23-MAG250_7105 (root@Server01.localdomain) (gcc version 4.2.4 (snapshot) (STMicroelectronics/Linux Base 4.2.4-44)) #2 PREEMPT Thu Jun 8 17:00:37 EEST 2017
Booting machvec: mag250
Node 0: start_pfn = 0x40000, low = 0x4f800
Zone PFN ranges:
Normal 262144 -> 325632
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 262144 -> 325632
Infomir,LLC MAG250 board initialisation
STx7105 version 4.x
Built 1 zonelists in Zone order. Total pages: 62992
Kernel command line: nwhwconf=device:eth0,hwaddr:00:1a:79:0e:21:da root=/dev/mtdblock6 rootfstype=jffs2 mem=160m bigphysarea=2048 ip=none mcman=on mtdparts=stm-nand-flex.1:4M(Kernel),120M(RootFs),4M(Kernel2),120M(Ro otFs2),-(Userfs) console=ttyAS0,115200
bpa2: partition 'bigphysarea' created at 0x41031000, size 8192 kB (0x00800000 B)
PID hash table entries: 1024 (order: 10, 4096 bytes)
Using tmu for system timer
Using 25.000 MHz high precision timer.
Console: colour dummy device 80x25
console [ttyAS0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 228864k/253952k available (3095k kernel code, 740k data, 2384k init)
PVR=04909200 CVR=60880000 PRR=00009e40
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STx7105
NET: Registered protocol family 16
Configuring FLASH for boot-from-NOR
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: SuperH clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.
JFS: nTxBlock = 1788, nTxLock = 14311
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
STMicroelectronics ASC driver initialized
stasc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stasc
stasc.1: ttyAS1 at MMIO 0xfd031000 (irq = 122) is a stasc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
platform registration... <7>done!
GMAC - user ID: 0x10, Synopsys ID: 0x33
eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
IO base addr: 0xfd110000)
STMMAC MII Bus: probed
eth0: PHY ID 02430c54 at 1 IRQ -1 (0:01) active
ICPlus IP101A: Registered new driver
ICPlus IP1001: Registered new driver
ICPlus IP175C: Registered new driver
physmap platform flash device: 00100000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 5 MTD partitions on "physmap-flash":
0x00000000-0x00050000 : "BootLoader"
first erase region 0 for slave @ 0
0x00050000-0x000a0000 : "Upgrade Boot"
first erase region 0 for slave @ 327680
0x000a0000-0x000e0000 : "User's FS"
first erase region 0 for slave @ 655360
0x000e0000-0x000f0000 : "Logo"
first erase region 0 for slave @ 917504
0x000f0000-0x00100000 : "BootLoader Enviroment"
first erase region 1 for slave @ 983040
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
stm-ehci stm-ehci.1: st-ehci
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
stm-ohci stm-ohci.1: stm-ohci
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st-coprocessor-0: No RAM reserved
st231.0 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
st-coprocessor-1: No RAM reserved
st231.1 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
stm_rng hardware driver 1.0 configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memoryzroute: SIOCADDRT: Network is down
net.core.rmem_max = 1000000
Starting S20uhdcp...
check_usbman:
check_mcman:mcman=on
## Error: "update_url" not defined
## Error: "mcip_img_conf" not defined
## Error: "mcport_img_conf" not defined
mcip_img=224.50.0.51
mcport_img=9001
## Error: "oppubKEY" not defined
Print recv_start to Monitor
PHY: 0:01 - Link is Up - 100/Full
Sat Jan 1 00:00:02 UTC 2000
IP: 192.168.243.249
MAC: ***********
Wrong offset in file /usr/bin/radix64.KEY -263 0

Signature not correct
Error: Not correct digital signature operator's key
Use default operator's keys
Connect to IP:224.50.0.51 port:9001
Create new file. File size:74600074
SN 0 offs 432480
Print recv_success to Monitor
Start Write Image to nand flash
4096+0 records in
4096+0 records out
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x00000000
Bad eraseblock 3 at 0x00060000
Bad eraseblock 8 at 0x00100000
Bad eraseblock 9 at 0x00120000
Bad eraseblock 10 at 0x00140000
Bad eraseblock 11 at 0x00160000
Bad eraseblock 16 at 0x00200000
Bad eraseblock 17 at 0x00220000
Bad eraseblock 18 at 0x00240000
Bad eraseblock 19 at 0x00260000
Bad eraseblock 24 at 0x00300000
Bad eraseblock 25 at 0x00320000
Bad eraseblock 26 at 0x00340000
Bad eraseblock 27 at 0x00360000
Bad eraseblock 32 at 0x00400000
Bad eraseblock 33 at 0x00420000
Bad eraseblock 34 at 0x00440000
Bad eraseblock 35 at 0x00460000
Bad eraseblock 40 at 0x00500000
Bad eraseblock 41 at 0x00520000
Bad eraseblock 43 at 0x00560000
Bad eraseblock 48 at 0x00600000
Bad eraseblock 49 at 0x00620000
Bad eraseblock 50 at 0x00640000
Bad eraseblock 51 at 0x00660000
Bad eraseblock 56 at 0x00700000
Bad eraseblock 57 at 0x00720000
Bad eraseblock 58 at 0x00740000
Bad eraseblock 59 at 0x00760000
Bad eraseblock 64 at 0x00800000
Bad eraseblock 65 at 0x00820000
Bad eraseblock 66 at 0x00840000
Bad eraseblock 67 at 0x00860000
Bad eraseblock 72 at 0x00900000
Bad eraseblock 83 at 0x00a60000
Bad eraseblock 282 at 0x02340000
Bad eraseblock 283 at 0x02360000
Bad eraseblock 380 at 0x02f80000
Bad eraseblock 497 at 0x03e20000
Bad eraseblock 537 at 0x04320000
Bad eraseblock 538 at 0x04340000
5 cmdlinepart partitions found on MTD device stm-nand-flex.1
Creating 5 MTD partitions on "stm-nand-flex.1":
0x00000000-0x00400000 : "Kernel"
0x00400000-0x07c00000 : "RootFs"
0x07c00000-0x08000000 : "Kernel2"
0x08000000-0x0f800000 : "RootFs2"
0x0f800000-0x10000000 : "Userfs"
Bad block at 0, 1 block(s) from 0 will be skipped
Bad block at 60000, 1 block(s) from 60000 will be skipped
Bad block at 100000, 1 block(s) from 100000 will be skipped
Bad block at 120000, 1 block(s) from 120000 will be skipped
Bad block at 140000, 1 block(s) from 140000 will be skipped
Bad block at 160000, 1 block(s) from 160000 will be skipped
Bad block at 200000, 1 block(s) from 200000 will be skipped
Bad block at 220000, 1 block(s) from 220000 will be skipped
Bad block at 240000, 1 block(s) from 240000 will be skipped
Bad block at 260000, 1 block(s) from 260000 will be skipped
Bad block at 300000, 1 block(s) from 300000 will be skipped
Bad block at 320000, 1 block(s) from 320000 will be skipped
Bad block at 340000, 1 block(s) from 340000 will be skipped
Bad block at 360000, 1 block(s) from 360000 will be skipped
Data did not fit into device, due to bad blocks
: Inappropriate ioctl for device
/usr/bin/img_write.sh: line 245: //: Permission denied
Bad block at 0, 1 block(s) from 0 will be skipped
Bad block at 60000, 1 block(s) from 60000 will be skipped
Bad block at 100000, 1 block(s) from 100000 will be skipped
Bad block at 120000, 1 block(s) from 120000 will be skipped
Bad block at 140000, 1 block(s) from 140000 will be skipped
Bad block at 160000, 1 block(s) from 160000 will be skipped
Bad block at 200000, 1 block(s) from 200000 will be skipped
Bad block at 220000, 1 block(s) from 220000 will be skipped
Bad block at 240000, 1 block(s) from 240000 will be skipped
Bad block at 260000, 1 block(s) from 260000 will be skipped
Bad block at 300000, 1 block(s) from 300000 will be skipped
Bad block at 320000, 1 block(s) from 320000 will be skipped
Bad block at 340000, 1 block(s) from 340000 will be skipped
Bad block at 360000, 1 block(s) from 360000 will be skipped
Data did not fit into device, due to bad blocks
: Inappropriate ioctl for device
Print write_error to Monitor
Wait command from operator
Log ip parameters must be set
Connect to IP: port:0

Да. Память убита.

[Chestr21]

днк, как сохранить лого? это не работает :

dd if=/dev/mtdblock3 of=~/logo.bmp.gz
gunzip logo.bmp.gz
gzip logo.bmp