Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

так что, пошло или нет?
описывай всё что делал, ведь ты не последний с этой проблемой

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

10 минут перекур, не хочу еще раз увидеть:

YAMON> load -b tftp://192.168.0.20/backup_kernel 0xb0100000
About to load tftp://192.168.0.20/backup_kernel
Press Ctrl-C to break
.................................................. ..............
.................................................. ..............
.................................................. ..............
................

Start = 0xb0100000, range = (0xb0100000,0xb077ffff), format = BINARY
Length = 0x680000 (6815744)
Checksum = 0x8c7

YAMON> pflash write -f 0x80000 0xb0100000 0x680000
0x00080000 - 0x006fffff will be erased
0x00080000 - 0x006fffff will be written
Erasing :
.................................................. ..............................
........................
Writing :
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................................................. ...............
Verifying (RAM 0xb0100000, size 0x680000) : Failed.
YAMON>

[makx]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Verifying (RAM 0xb0100000, size 0x680000) : Failed.

Если ты на это, то может flash ROM на матери устал ?
Бывают, что дохнут...

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Я уже не знаю, но ведь пишет:
xenv cs2 ok
power supply: ok
dram0 ok (
dram1 ok (9)
zboot (0) ok
>
,а при тесте:
YAMON> test
Testing ALL
Testing RAM
Memory test from 0xB1105600 to 0xBFFFFFFC, 10 loops.
Now running loop 1 |
Failed at address: 0xB7A00000
Written    Read      Difference Re-Read
0xE0F8D087 0x00000000 0xE0F8D087 0x00000000
0x77238028 0x00000000 0x77238028 0x00000000
0xECE05E1F 0x00000000 0xECE05E1F 0x00000000
0x306D94D0 0x00000000 0x306D94D0 0x00000000
0x36CA7D37 0x00000000 0x36CA7D37 0x00000000
0x7BE47BF8 0x00000000 0x7BE47BF8 0x00000000
0x9F13C5CF 0x00000000 0x9F13C5CF 0x00000000
0x43B5DDA0 0x00000000 0x43B5DDA0 0x00000000

Test failed 
YAMON>

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

походу раму пипец пришел и откат на нормальную частоту уже не поможет

[makx]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

походу раму пипец пришел

При разгоне не только частота проца поднимается, а так же поднимается частота
системной шины, на который RAM сидит

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

YAMON> tesstt bist
Testing BIST
mpeg0...
MASK=0x1ffffff, PASS=0x1ffffff pass!
audio0...
MASK=0x7, PASS=0x7 pass!
mpeg1...
MASK=0x1ffffff, PASS=0x1ffffff pass!
audio1...
MASK=0x7, PASS=0x7 pass!
demux...
MASK=0x1ffff, PASS=0x1ffff pass!
Test passed

А еще это как можно проверить?

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

как, так как ты делал много раз, залить файл в память и проверить есть ли он там

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Прошил:
load -b tftp://192.168.0.20/backup_kernel 0xb0100000
pflash write -f 0x80000 0xb0100000 0x680000

Writing :
.................................................. ..............................
.................................................. ..............................
.................................................. ...............
Verifying (RAM 0xb0100000, size 0x680000) : OK.
YAMON>

Урааа, память жива, а что дальше?

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

вроде как делать по той инструкции из которой ты выдрал эту комманду

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Не пойму?:
Testing ALL
Testing RAM
Memory test from 0xB1105600 to 0xBFFFFFFC, 10 loops.
Now running loop 1 |
Failed at address: 0xB7A00000
Written Read Difference Re-Read
0xE0F8D087 0x00000000 0xE0F8D087 0x00000000
0x77238028 0x00000000 0x77238028 0x00000000
0xECE05E1F 0x00000000 0xECE05E1F 0x00000000
0x306D94D0 0x00000000 0x306D94D0 0x00000000
0x36CA7D37 0x00000000 0x36CA7D37 0x00000000
0x7BE47BF8 0x00000000 0x7BE47BF8 0x00000000
0x9F13C5CF 0x00000000 0x9F13C5CF 0x00000000
0x43B5DDA0 0x00000000 0x43B5DDA0 0x00000000

Test failed
YAMON>

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

чё понимать, какойто кусок сдох.
но это может быть и не проблема, как у харда плохие сектора.
может ты всётаки начнешь дальше делать по инструкции и писать, что получилось?
уже начинает бесить, когда ты спрашиваешь, потом получаешь ответ и делаешь дальше по своему...

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Был в ресивере, но он завис (не успел выбрать обновиться с USB):

Spoiler

YAMON> load -b tftp://192.168.0.10/xrpc_xload_vmlinux_ES4_prod.bin 0x90020000
About to load tftp://192.168.0.10/xrpc_xload_vmlinux_ES4_prod.bin
Press Ctrl-C to break
.................................................. ..............
.................................................. ..............
.................................................. ..............
.........

Start = 0x90020000, range = (0x90020000,0x9066bf43), format = BINARY
Length = 0x64bf44 (6602564)
Checksum = 0xb57b7a66

YAMON> dump romfs 0x90020000
ROMFS not found from 0x90020000 to 0x90020100
YAMON> xxrrppcc  00xx9900002200000000
xrpc succeeded
YAMON> llooaadd  zzbbff  00xxbb33000000000000
  Checking zboot signature..  it's a zboot file, signature OK.
  Decompressing to 0x90020000 ..
Output length: 0x0096843a(9864250)
load compressed zboot file from 0xb3000000 to 0x90020000 OK
YAMON> ggoo
em86xx_eth ethernet stop
Linux version 2.6.15-sigma (kevin@kevin-laptop) (gcc version 3.4.2) #138 PREEMPT
Thu Jan 22 21:35:07 KST 2009
Configured for SMP863x (revision ES6/RevA), detected SMP8634 (revision ES9/RevC)
.
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
memory: 02fe0000 @ 10020000 (usable)
User-defined physical RAM map:
memory: 06be0000 @ 10020000 (usable)
On node 0 totalpages: 93184
  DMA zone: 93184 pages, LIFO batch:31
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line: console=ttyS0 root=dev/sda1 rw rootdelay=10 mem=108m
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 150.188 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 97280k/110464k available (4425k kernel code, 13164k reserved, 1007k data
, 4200k init, 0k highmem)
Calibrating delay loop... 296.96 BogoMIPS (lpj=148480)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB
PCI: device 1 disabled
PCI: device 4 disabled
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x16c00000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
tangox frequency scaling module installed.
Created /proc/cpucache_info entry.
NTFS driver 2.1.25 [Flags: R/W DEBUG].
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (now
ayout= 0)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: loaded (max 8 devices)
nbd: registered device at major 43
tango2_enet: ethernet driver for SMP863x internal mac
tango2_enet: detected phy at address 0x01
tango2_enet: mac address 00:02:14:16:b6:35
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...
hda: DM255610V010, ATA DISK drive
hda: no 80 conductors cable, falling back to lower udma mode
hda: set to Ultra DMA mode 2
ide0: DMA enabled for ATA DISK hda
ide0 at 0x223c0-0x223c7,0x22398 on irq 26
hda: max request size: 128KiB
hda: 501760 sectors (256 MB) w/1KiB Cache, CHS=980/16/32, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
physmap flash device CS2: 800000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using physmap partition definition
Adding partition #1-#5
Creating 5 MTD partitions on "CS2: Physically mapped flash":
0x00000000-0x00020000 : "CS2-Part1"
0x00020000-0x00040000 : "CS2-Part2"
0x00040000-0x00080000 : "CS2-Part3"
0x00080000-0x00700000 : "CS2-Part4"
0x00700000-0x00800000 : "CS2-Part5"
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21
2005 UTC).
usbcore: registered new driver snd-usb-audio
ALSA device list:
  No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 4200k freed
mount: /etc/mtab: No such file or directory
Initializing random number generator... done.
===> Starting system configuration...
===> [0] replace busybox 1.15.2(udhcpc, ftpget, ftpput)
===> [1] VFD initializing...
[td210] INITIALIZED END
[td210] SLEEP MODE OFF
===> [2] USB 2.0 driver loading...
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/uhci-hcd.ko
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:00:02.0 (0000 -> 0001)
uhci_hcd 0000:00:02.0: UHCI Host Controller
uhci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:02.0: irq 22, io base 0x58000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:02.1 (0000 -> 0001)
uhci_hcd 0000:00:02.1: UHCI Host Controller
uhci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:02.1: irq 22, io base 0x58000020
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Using /lib/modules/2.6.15-sigma/kernel/drivers/usb/host/ehci-hcd.ko
PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 22, io mem 0x60008000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
===> [3] File system checking...
check hda
Disk /dev/hda: 256 MB, 256901120 bytes
/dev/hda1               1         560      143359+  83  Linux
/dev/hda2             561         624       16384   83  Linux
/dev/hda3             625         656        8192   83  Linux
/dev/hda4             657         980       82944   83  Linux
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
check hdb
Cannot find HDD
===> [4] Make device files
mknod: /dev/mum0: File exists
mknod: /dev/em8xxx0: File exists
===> [5] Export hostname
Starting network...
>> pre-up start...
route: SIOC[ADD|DEL]RT: No such process
>> pre-up end...
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
===> Starting services...
===> [1] telnetd starting...
===> Starting MMP custom setting...

AZBox login: llad: module license 'LGPL' taints kernel.
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1570] init_module: begun
em8xxx0 [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP8
634_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.w
ork/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1431] identify: board as unkno
wn subid
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1556] identify: device 0x8634 0
x86 accepted with software tango2revA
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1635] mumk_register_tasklet 0xc
809a000
mumk_register_tasklet: (0) tasklet c809a000 status @c8da3ea4
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[0] 0xc80a7000: pE=0xc8da3c80 ch_idx=33 module_id=0x3c 0xc8da3ca0
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[1] 0xc80a9000: pE=0xc8da3c80 ch_idx=35 module_id=0x3c 0xc8da3cac
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[2] 0xc80ab000: pE=0xc8da3c80 ch_idx=41 module_id=0x13c 0xc8da3cb8
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[3] 0xc80ad000: pE=0xc8da3c80 ch_idx=43 module_id=0x13c 0xc8da3cc4
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[4] 0xc80af000: pE=0xc8da3c80 ch_idx=37 module_id=0x23c 0xc8da3cd0
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[5] 0xc80b1000: pE=0xc8da3c80 ch_idx=39 module_id=0x23c 0xc8da3cdc
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
34_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nodts.wo
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_task
let[6] 0xc80b3000: pE=0xc8da3c80 ch_idx=69 module_id=0x3f 0xc8da3ce8
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
em8xxx [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_SMP86
rk/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1732] init_module: done. Found
1 em8xxx
>>>>>>> CONFIG_TANGO2 :: HZ = 1000
scard: SMP8634 driver loaded (rd_buffer_size = 288, wr_buffer_size = 288, freq =
3600000)
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Seri
al Device
usbcore: registered new driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
cdfs 2.6.27 loaded.
fuse: Unknown symbol r4k_flush_cache_page
PCI: Enabling device 0000:00:03.0 (0000 -> 0002)
RT61: Vendor = 0x1814, Product = 0x0301
PCI: Setting latency timer of device 0000:00:03.0 to 64
rtusb init --->
usbcore: registered new driver rt2870
RT61: RfIcType= 3
    em8xxx0 [/DATA/Yellow.mine/Working/SigmaDesign8634/SMP8634-2850.gcc3.4/mrua_
SMP8634_v2_8_5_1_celrun_lg_branch_10212009-HDMI-fix_facsprod_legacy_dev.mips.nod
ts.work/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1237] EMhwlibUnregisterCle
anable module 45, prop 4543 (from rmmod em8xxx_id 827): not found
usb 3-2: new high speed USB device using ehci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
  Vendor: Generic   Model: Flash Disk        Rev: 8.07
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 1006080 512-byte hdwr sectors (515 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 1006080 512-byte hdwr sectors (515 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
oom-killer: gfp_mask=0x201d2, order=0
Mem-info:
DMA per-cpu:
cpu 0 hot: low 0, high 186, batch 31 used:134
cpu 0 cold: low 0, high 62, batch 15 used:13
DMA32 per-cpu: empty
Normal per-cpu: empty
HighMem per-cpu: empty
Free pages:        3592kB (0kB HighMem)
Active:15391 inactive:2810 dirty:0 writeback:0 unstable:0 free:898 slab:4014 map
ped:13183 pagetables:625
DMA free:3592kB min:2440kB low:3048kB high:3660kB active:61564kB inactive:11240k
B present:372736kB pages_scanned:305196 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
DMA32 free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB page
s_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
Normal free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB pag
es_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
HighMem free:0kB min:128kB low:128kB high:128kB active:0kB inactive:0kB present:
0kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
DMA: 160*4kB 49*8kB 4*16kB 2*32kB 0*64kB 1*128kB 1*256kB 0*512kB 0*1024kB 1*2048
kB 0*4096kB = 3592kB
DMA32: empty
Normal: empty
HighMem: empty
Swap cache: add 0, delete 0, find 0/0, race 0+0
Free swap  = 0kB
Total swap = 0kB
Free swap:            0kB
93184 pages of RAM
0 pages of HIGHMEM
67809 reserved pages
1049 pages shared
0 pages swap cached
Out of Memory: Killed process 966 (DStar).
oom-killer: gfp_mask=0x201d2, order=0
Mem-info:
DMA per-cpu:
cpu 0 hot: low 0, high 186, batch 31 used:154
cpu 0 cold: low 0, high 62, batch 15 used:24
DMA32 per-cpu: empty
Normal per-cpu: empty
HighMem per-cpu: empty
Free pages:       17176kB (0kB HighMem)
Active:12277 inactive:2526 dirty:0 writeback:0 unstable:0 free:4294 slab:4015 ma
pped:9735 pagetables:609
DMA free:17116kB min:2440kB low:3048kB high:3660kB active:49108kB inactive:10172
kB present:372736kB pages_scanned:1584 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
DMA32 free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB page
s_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
Normal free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB pag
es_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
HighMem free:0kB min:128kB low:128kB high:128kB active:0kB inactive:0kB present:
0kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0 0
DMA: 565*4kB 399*8kB 163*16kB 69*32kB 23*64kB 14*128kB 4*256kB 1*512kB 0*1024kB
1*2048kB 0*4096kB = 17116kB
DMA32: empty
Normal: empty
HighMem: empty
Swap cache: add 0, delete 0, find 0/0, race 0+0
Free swap  = 0kB
Total swap = 0kB
Free swap:            0kB
93184 pages of RAM
0 pages of HIGHMEM
67809 reserved pages
1087 pages shared
0 pages swap cached
Out of Memory: Killed process 954 (CRTVCore).
Out of Memory: Killed process 931 (CRTVCore).
Out of Memory: Killed process 955 (CRTVCore).
Out of Memory: Killed process 987 (CRTVCore).
Out of Memory: Killed process 988 (CRTVCore).
Out of Memory: Killed process 989 (CRTVCore).
Out of Memory: Killed process 990 (CRTVCore).
Out of Memory: Killed process 991 (CRTVCore).
Out of Memory: Killed process 992 (CRTVCore).
Out of Memory: Killed process 993 (CRTVCore).

[nitrogen14]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

ну хоть какойто прогресс, что был в ресивере.
чем дальше, тем больше походит на то, что рам битый.
пробуй и другое способа о которых писали ранее и которые ты пробовал до этого

load -b tftp://192.168.1.3/backup_kernel 0xb0100000
pflash write -f 0x80000 0xb0100000 0x680000
After that you should see Erasing and Writing, it will take a while, but after it finish you just reboot and you are back with original kernel and you can continue to upgrade FW over USB ....

[VVZ]

Re: Azbox RS232(PC)->TTL(AZ) / USB(PC)->TTL(AZ) & YAMON - побеждаем вечный "BOOTING"

Зашел в меню, перепрошил с флехи, перезагрузился
последние строчки:
CMD: /bin/mkdir -p '/DISK2/message'
mem=107m console=ttyS0,115200
6
/tmp/local
Fail to Receive ACK

и BOOTING, не помогло...