TD1200A[~]$ cat /proc/cpuinfo
system type : Sigma Designs TangoX
processor : 0
cpu model : MIPS 24K V7.12 FPU V0.0
Initial BogoMIPS : 331.77
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes
ASEs implemented : mips16
shadow register sets : 1
VCED exceptions : not available
VCEI exceptions : not available

System bus frequency : 333000000 Hz
CPU frequency : 499500000 Hz
DSP frequency : 333000000 Hz

TD1200A[~]$ dmesg
000] CPU revision is: 0001937c
[ 0.000000] FPU revision is: 01739300
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 06400000 @ 04000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 07800000 @ 04000000 (usable)
[ 0.000000] Wasting 131072 bytes for tracking 4096 unused pages
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] On node 0 totalpages: 11776
[ 0.000000] DMA zone: 23 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 11753 pages, LIFO batch:1
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Built 1 zonelists. Total pages: 11753
[ 0.000000] Kernel command line: console=ttyS0 mem=120M
[ 0.000000] Primary instruction cache 32kB, 4-way, physically tagged, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, physically tagged, no aliases, linesize 32 bytes
[ 0.000000] Synthesized TLB refill handler (20 instructions).
[ 0.000000] Synthesized TLB load handler fastpath (32 instructions).
[ 0.000000] Synthesized TLB store handler fastpath (32 instructions).
[ 0.000000] Synthesized TLB modify handler fastpath (31 instructions).
[ 0.000000] Cache parity protection disabled
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Using 249.750 MHz high precision timer.
[ 0.000000] Console: colour dummy device 80x25
[ 0.001000] Dentry cache hash table entries: 32768 (order: 3, 131072 bytes)
[ 0.002000] Inode-cache hash table entries: 16384 (order: 2, 65536 bytes)
[ 0.006000] Memory: 110448k/122880k available (3224k kernel code, 12368k reserved, 728k data, 7440k init, 0k highmem)
[ 0.007000] Calibrating delay loop... 331.77 BogoMIPS (lpj=16588
[ 0.030000] Mount-cache hash table entries: 2048
[ 0.032000] NET: Registered protocol family 16
[ 0.033000] PCI: Initializing SMP86xx PCI host controller
[ 0.035000] PCI: Remapped PCI I/O space 0x58000000 to 0xc0000000, size 64 kB
[ 0.036000] PCI: Remapped PCI config space 0x50000000 to 0xc0018000, size 10 kB
[ 0.037000] PCI: Configured SMP86xx as PCI slave with 1024MB PCI memory
[ 0.038000] PCI: Region size is 131072KB
[ 0.039000] PCI: Map DMA memory 0x04000000-0x0b800000 for PCI at 0x48000000
[ 0.046000] SCSI subsystem initialized
[ 0.047000] libata version 2.21 loaded.
[ 0.048000] usbcore: registered new interface driver usbfs
[ 0.049000] usbcore: registered new interface driver hub
[ 0.050000] usbcore: registered new device driver usb
[ 0.052000] Time: MIPS clocksource has been installed.
[ 0.054000] NET: Registered protocol family 2
[ 0.064000] IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
[ 0.065000] TCP established hash table entries: 8192 (order: 2, 65536 bytes)
[ 0.066000] TCP bind hash table entries: 8192 (order: 1, 32768 bytes)
[ 0.067000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.068000] TCP reno registered
[ 1.930000] NTFS driver 2.1.28 [Flags: R/W DEBUG].
[ 1.931000] fuse init (API version 7.Крутой
[ 1.932000] io scheduler noop registered
[ 1.933000] io scheduler anticipatory registered
[ 1.934000] io scheduler deadline registered
[ 1.935000] io scheduler cfq registered (default)
[ 2.199000] tango3dog: Hardware Watchdog Timer for SMP864x/SMP865x 0.1 (def. timeout: 30 sec)
[ 2.200000] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
[ 2.201000] serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
[ 2.202000] serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
[ 2.206000] loop: module loaded
[ 2.207000] tangox_enet0: ethernet mac_core 0 support is disabled from XENV
[ 2.208000] tangox_enet1: detected phy at address 0x01
[ 2.209000] tangox_enet1: Ethernet driver for SMP864x/SMP865x internal MAC core 1: 100Mbps Base at 0x26800
[ 2.213000] tangox_enet1: mac address 00:02:14:17:98:73
[ 2.214000] SCSI Media Changer driver v0.25
[ 2.215000] driver tangox-ehci-hcd, 10 Dec 2004
[ 2.216000] TangoX USB initializing...
[ 2.241000] tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
[ 2.242000] tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
[ 2.243000] tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021400
[ 2.250000] tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.251000] usb usb1: configuration #1 chosen from 1 choice
[ 2.252000] hub 1-0:1.0: USB hub found
[ 2.253000] hub 1-0:1.0: 2 ports detected
[ 2.355000] tangox-ohci-hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.356000] TangoX USB was initialized.
[ 2.357000] Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
[ 2.358000] tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
[ 2.359000] tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
[ 2.360000] tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
[ 2.476000] usb usb2: configuration #1 chosen from 1 choice
[ 2.477000] hub 2-0:1.0: USB hub found
[ 2.478000] hub 2-0:1.0: 2 ports detected
[ 2.580000] Initializing USB Mass Storage driver...
[ 2.581000] usbcore: registered new interface driver usb-storage
[ 2.582000] USB Mass Storage support registered.
[ 2.583000] mice: PS/2 mouse device common for all mice
[ 2.584000] usbcore: registered new interface driver usbhid
[ 2.585000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.586000] TCP cubic registered
[ 2.587000] NET: Registered protocol family 1
[ 2.588000] NET: Registered protocol family 17
[ 2.624000] Freeing unused kernel memory: 7440k freed
[ 2.788000] sigmablock: module license 'Proprietary' taints kernel.
[ 2.792000]
[ 2.792000] CS 0 vendor id 0xec.......
[ 2.793000] CS 0 device id 0xda.......
[ 2.794000] ...chip_index 0 pos 0
[ 2.828000]
[ 2.828000] CS 1 vendor id 0x00.......
[ 2.829000] CS 1 device id 0x00.......
[ 2.830000] nand_probe Error on chip 1 ret code -13
[ 4.703000] kjournald starting. Commit interval 5 seconds
[ 4.710000] EXT3 FS on sigmblockg, internal journal
[ 4.712000] EXT3-fs: mounted filesystem with journal data mode.
[ 5.106000] kjournald starting. Commit interval 5 seconds
[ 5.114000] EXT3 FS on sigmblockh, internal journal
[ 5.116000] EXT3-fs: mounted filesystem with journal data mode.
[ 5.342000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 13.222000] k_name=Tangox SATA 0 driver=Tangox SATA 0
[ 13.223000] SATA version 0x3139302a ID 0x0 is detected
[ 13.229000] scsi0 : Tangox SATA 0
[ 13.230000] ata1: SATA max UDMA/133 cmd 0xa0023000 ctl 0xa0023020 bmdma 0xcdcdcdcd irq 49
[ 13.685000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 13.689000] ata1.00: ATA-7: ST920217AS, 3.01, max UDMA/100
[ 13.690000] ata1.00: 39070080 sectors, multi 0: LBA48 NCQ (depth 0/1)
[ 13.694000] ata1.00: configured for UDMA/100
[ 13.695000] scsi 0:0:0:0: Direct-Access ATA ST920217AS 3.01 PQ: 0 ANSI: 5
[ 13.696000] ata1: dev 0 max request 256 sectors (lba4
[ 13.697000] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors (20004 MB)
[ 13.698000] sd 0:0:0:0: [sda] Write Protect is off
[ 13.699000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.700000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.701000] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors (20004 MB)
[ 13.702000] sd 0:0:0:0: [sda] Write Protect is off
[ 13.703000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.704000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.705000] sda: sda1
[ 13.732000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.733000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.734000] k_name=Tangox SATA 1 driver=Tangox SATA 1
[ 13.735000] SATA version 0x3139302a ID 0x0 is detected
[ 13.741000] scsi1 : Tangox SATA 0
[ 13.742000] ata2: SATA max UDMA/133 cmd 0xa0023800 ctl 0xa0023820 bmdma 0xcdcdcdcd irq 62
[ 14.046000] ata2: SATA link down (SStatus 0 SControl 300)
[ 16.068000] em8xxx [/opt/smp8654_370/mrua_SMP8654F_3_7_0_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1571] init_module: begun

TD1200A[~]$ cat /proc/meminfo
MemTotal: 117952 kB
MemFree: 13024 kB
Buffers: 1104 kB
Cached: 48816 kB
SwapCached: 0 kB
Active: 71536 kB
Inactive: 10624 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 32288 kB
Mapped: 19888 kB
Slab: 14016 kB
SReclaimable: 1264 kB
SUnreclaim: 12752 kB
PageTables: 1424 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
CommitLimit: 58976 kB
Committed_AS: 160912 kB
VmallocTotal: 1048272 kB
VmallocUsed: 3392 kB
VmallocChunk: 1044416 kB

и что в итоге туда заливать?

подрубился по рс232, распиновка как и у всех целрунов



имя/пасс стандартные для азеров рут/азбокс

лог

**********************
* YAMON ROM Monitor Tiger v0.3
* Revision 02.13-SIGMADESIGNS-01-R2.13-7
**********************************
Memory: code: 0x85000000-0x85040000, 0x85200000-0x85204000
reserved data: 0x85240000-0x86440000, PCI memory: 0x86440000-0x86840000
NAND FLASH Driver Version [ S I G M 1.0.2 ] on CS 0
!! No NAND hardware found on CS 1 !!
Environment variable 'start' exists. After 2 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

y.start "xrpc 0xac080090;load zbf 0xb3000000;go 0x90020000"

dis

SYNOPSIS
dis [-m] [-16] <address> [<count>]

DESCRIPTION
Disassemble code starting at <address>.

Disassembles MIPS64/MIPS32 instructions.
Includes MIPS-3D(TM) and MIPS16e(TM) ASEs.
Includes MIPS64/MIPS32 Release 2 instructions.

<count> (default 16) specifies the number of instructions to disassemble.

The continuation command '.' works together with 'dis'.

OPTIONS
-m Prompt user for keypress after each screen of data
-16 Disassemble MIPS16e code